Tag Archives: cisco

Cisco 867VAE

Probably the best ADSL router I have had to date. Slightly more expensive than a DG834v4 but infinitely more versatile.
This one has the Broadcom chipset which blows  away the one in the 877.
I’m also running two ipv6 tunnels, one to SixXs and one to Hurricane Electric.
The only feature I found lacking was IGPs – It doesn’t support OSPF or Cisco’s proprietary EIGRP. OK it does have good ol’ RIP v1 and v2.

NickB uptime is 9 weeks, 5 days, 15 hours, 5 minutes

Stays up for a while… Good stable ADSL2+ Annexe A and Annexe M performance.

Continue reading

IOS backup and Upgrade for Cisco Aironet APs

IOS Version 1130-k9w7-mx.124-10b.JA needed Internet Explorer version 6 for web configuration.

I obtained an AP-1242AG with a later IOS version 1240-k9w7-mx.124-21a.JA1. Checking the release notes for this version revealed that Firefox browser was now supported.

I then obtained a copy of 1130-k9w7-mx.124-21A.JA1 to upgrade my 1130.
Continue reading

Installing SDM On a Dynamips or GNS3 Router

I’ve seen several comments on the forums where folk have not been able to install SDM to the router memory. The IOS is usually a 12.4T series one. Here is a workaround which involves using a 12.4 or earlier IOS. In this case I used a 3725 with a 64MB flash card.
First attempt to install onto 12.4T with empty flash – reports

"Unable to eastablish connection with the router"

Continue reading

SDM on Dynamips/GNS3 Routers

I’m a long way from home and my real router lab this week so having to make do with the amazing DynaMips emulator, which just happens to run real IOS images. I have the choice of running this either with the Dynagen package on Mac OSX or GNS3 on Windows.

I wanted to configure some C3725 images for CCNA Security simulations and as part of that, install SDM 2.5 into the router flash memory. Unfortunately this proved difficult with IOS 12.4T but I managed to persist and find a workaround.

First attempts using IOS c3725-advsecurityk9-mz.124-15.T14.extracted.bin – No luck, the Windows SDM installer continually fails with the message “Unable to establish connection with the router”.

So next I roll back my IOS to c3725-advsecurityk9-mz.124-25d – I ran the installer again and was able to load SDM into the virtual router flash.

Finally, re-configure with IOS 12.4T and I can launch SDM running on the router

Cisco Console Cable Differences

The console cable RS232 lines used vary between Routers and Catalyst Switches.

  • Router console does not use RTS/CTS (pins 1 and 8).
  • Router aux port uses all pins.

Reference:
Auxiliary Port, Console Port, And Adapter Pinouts For Cisco 1000, 1600, 2500, 2600, And 3600 Series Routers

  • Some Catalyst switches do not use DSR/DTR (pins 2 and 7) but do use RTS/CTS (pins 1 and 8).

Reference:
Connecting a Terminal to the Console Port on Catalyst Switches

This solves an issue I’ve been having with connecting some Catalyst switches to my Lantronix ETS-16 terminal server – the cables are only connected to RJ45 pins 2-7. The solution is to make up a cable with 1 looped to 8 (RTS – CTS) on the RJ45.

The Cisco RJ45 – 9D-Female rollover cable works perfectly as I would expect!

Setting Your Source Interface

Problem: I’ve set up VPN between the LANs on two routers and I want to test the link from LAN 1 to LAN 3.

192.168.1.1/24--[R1]--10.1.1.0/30--[R2]--10.2.2.0/30--[R3]--192.168.3.1/24

Default ping/telnet/ssh will fail because it will use the source address of the interface closest to the destination.

R1#ping 192.168.3.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.2.1, timeout is 2 seconds:
U.U.U
Success rate is 0 percent (0/5)

Solutions: Continue reading

SDM Part II

I’ve finally reached a working solution for SDM with the aid of the brilliant multi-platform VirtualBox. I can run this set-up on OSX Snow Leopard or XP/Vista.

I used a Windows 2000 Professional VM that I had available and I’ve set it up to meet the SDM requirements.

  • Internet Explorer 6 SP1 as w2K ships with IE5.
  • Java JRE 1.6.0_03 – This can be found in the Oracle Java Archives.
  • Disable Java Updates in the Java settings in Windows Control Panel.
  • Set the Java User Runtime parameter to -Xmx256m in Java Runtime Environment Settings, otherwise you’ll get an error message from SDM when you try and access the IPS menu item.
  • Install SDM 2.5.

Please understand that W2K is no longer supported by MS so this should only be used for SDM in a controlled environment. Continue reading

Security Device Mangler

SDM 2.5I originally rubbed shoulders with Cisco’s Router and Security Device Manager, known to most people as SDM, during my ICND1 studies. Whilst it seemed to work well enough to do NAT and other basic router tasks, I was never satisfied it was working properly for me. As I have now decided to progress with the CCNA Security studies, I find that SDM is central to these and now I have managed get it working 100%! Continue reading

No Console

Everything was going well with my remote console session R2002 until I decided to clear the configs…

erase startup-config
Reload

Then nothing. So I go and visit the site (OK, climb the stairs and turn left) and do a physical check. Power lights look OK. Then I spotted it – I’d plugged the console cable into the AUX socket. Port is never enabled because the router is sitting there at the

Would you like to enter the initial configuration dialog? [yes/no]:

prompt, which means the AUX line is not yet enabled. Of course there’s a security issue here as I should have shutdown the AUX port in the first place!

Plug moved one socket to the left (HINT – SKY BLUE). Normal operation restored, now I can get on with the task of configuring it to be a frame-relay switch.